IO::Interactive - Utilities for interactive I/O |
IO::Interactive - Utilities for interactive I/O
This document describes IO::Interactive version 0.0.6
use IO::Interactive qw(is_interactive interactive busy);
if ( is_interactive() ) { print "Running interactively\n"; }
# or...
print {interactive} "Running interactively\n";
$fh = busy { do_noninteractive_stuff(); }
This module provides three utility subroutines that make it easier to develop interactive applications...
is_interactive()
*ARGV
and the currently selected
filehandle (usually *STDOUT
) are connected to the terminal. The
test is considerably more sophisticated than:
-t *ARGV && -t *STDOUT
as it takes into account the magic behaviour of *ARGV
.
You can also pass is_interactive
a writable filehandle, in which case it
requires that filehandle be connected to a terminal (instead of the
currently selected). The usual suspect here is *STDERR
:
if ( is_interactive(*STDERR) ) { carp $warning; }
interactive()
*STDOUT
if is_interactive
is true. If
is_interactive()
is false, interactive
returns a filehandle that
does not print.
This makes it easy to create applications that print out only when the application is interactive:
print {interactive} "Please enter a value: "; my $value = <>;
You can also pass interactive
a writable filehandle, in which case it
writes to that filehandle if it is connected to a terminal (instead of
writinbg to *STDOUT
). Once again, the usual suspect is *STDERR
:
print {interactive(*STDERR)} $warning;
busy {...}
*ARGV
is temporarily replaced by a closed
filehandle. That is, no input from *ARGV
is possible in a busy
block.
Furthermore, any attempts to send input into the busy
block through
*ARGV
is intercepted and a warning message is printed to *STDERR
.
The busy
call returns a filehandle that contains the intercepted input.
A busy
block is therefore useful to prevent attempts at input when the
program is busy at some non-interactive task.
IO::Interactive requires no configuration files or environment variables.
This module requires the openhandle()
subroutine from the
Scalar::Util module.
None reported.
No bugs have been reported.
Please report any bugs or feature requests to
bug-io-interactive@rt.cpan.org
, or through the web interface at
http://rt.cpan.org.
Damian Conway <DCONWAY@cpan.org>
Currently maintained by brian d foy <bdfoy@cpan.org>
Copyright (c) 2005, Damian Conway <DCONWAY@cpan.org>
. All rights reserved.
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
BECAUSE THIS SOFTWARE IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE SOFTWARE, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE SOFTWARE ``AS IS'' WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE SOFTWARE IS WITH YOU. SHOULD THE SOFTWARE PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR, OR CORRECTION.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE SOFTWARE AS PERMITTED BY THE ABOVE LICENCE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE SOFTWARE (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE SOFTWARE TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
IO::Interactive - Utilities for interactive I/O |